Colombia Plastic Polypropylene PP Biaxial Uniaxial Geogrids for Construction

HDPE uniaxial geogrid is manufactured from select grades of High Density Polyethylene, from the process of extruding and longitudinal stretching.

Category:

ColombiaPP/HDPE Uniaxial Geogrid

Phone:+86 13105487610

Product Description

Introduction

The homes of Biaxial Geogrids, made of Polypropylene (PP) with their rectangular apertures, excessive tensile electricity and optimised geometry of nodes and ribs make them equal to any different comparable material. The reinforcing motion of PP Biaxial Geogrids lies mostly in confining soil and growing its shearing resistance by using a technique of interlocking between the rectangular ribs and the soil.
The load dispersal impact from the interlocking mechanism is surprisingly positive and can limit sub-base thickness and building cost. PP Biaxial Geogrids can be used with any sort of mechanical fill material. Two aperture measurement degrees are handy for superior matching with venture fill.

Video Showcase

Applications

Increase the bearing ability of the roadbed and foundation and extend their carrier life.
Prevent street floor and basis from sinking or flawing, maintain smooth and lovely floor surface.
Convenient building saves time and labor, minimize mounting time and limit renovation expense.
Prevent culverts from flawing.
Enhance earth slope and forestall water loss and soil erosion.
Decrease underlayer thickness and shop manufacturing cost.
nhance the steadiness of aspect slope turf internet patch to enhance greening.
Replace wire netting used in mine as intermediate ceiling netting.

Working Drawing

Specifications

Index Properties	Test Method	Unit	UX60PE	UX80PE	UX90PE	UX120PE	UX130PE	UX160PE	UX170PE	UX180PE
Polymer	-		HDPE	HDPE	HDPE	HDPE	HDPE	HDPE	HDPE	HDPE
Minimum Carbon Black	ASTM D4218	%	2	2	2	2	2	2	2	2
Ultimate Tensile Strength,MD	ASTM D6637	kN/m	60	80	90	120	130	160	170	180
Tensile Strength @2%Strain,MD	ASTM D6637	kN/m	16	21	24	33	38	47	49	52
Tensile Strength @5%Strain,MD	ASTM D6637	kN/m	31	40	45	65	75	93	96	103
Strain@UltimateStrength,MD	ASTM D6637	%	11.5	11.5	11.5	11.5	11.5	11.5	11.5	11.5
Junction Efficiency	GRI GG2-87	%	93	93	93	93	93	93	93	93
Flexural Rigidity	ASTM D1388	mg-cm	530,000	1,150,000	2.300,000	6,050,000	6,400,000	8,600,000	8,900,000	9,100,000
UV Resistance	ASTM D4355	%	98	98	98	98	98	98	98	98
Minimum Reduction Factor for Installation Damage (RFid)	ASTM D5818	-	1.05	1.05	1.05	1.05	1.05	1.05	1.05	1.05
Reduction Factor for Creep for 120-year Design Life (RFcr)	ASTM D5262	-	2.6	2.6	2.6	2.6	2.6	2.6	2.6	2.6
Roll Width	-	m	1/1.3/2	1/1.3/2	1/1.3/2	1/1.3/2	1/1.3/2	1/1.3/2	1/1.3/2	1/1.3/2
Roll Length	-	m	100	50	50	50	50	50	50	50